[Snort-users] Fwd: Snort 2.9.6.0 memory leak?

Mirek Suliba msuliba at ...11827...
Thu Feb 27 16:15:09 EST 2014


Hi Hui,

I allowed traffic to go through this server only for three hours and I
disabled it when I saw this constant memory usage growth. Below is output
from kill -USR1 [Snort_PID] command:

Feb 27 15:04:06 rsyslogd-2177: imuxsock lost 14 messages from pid 23167 due
to rate-limiting
Feb 27 15:04:06 snort[23167]: *** Caught Dump Stats-Signal
Feb 27 15:04:06 snort[23167]:
===============================================================================
Feb 27 15:04:06 snort[23167]: Memory usage summary:
Feb 27 15:04:06 snort[23167]:   Total non-mmapped bytes (arena):
183816192
Feb 27 15:04:06 snort[23167]:   Bytes in mapped regions (hblkhd):
313253888
Feb 27 15:04:06 snort[23167]:   Total allocated space (uordblks):
76144432
Feb 27 15:04:06 snort[23167]:   Total free space (fordblks):
107671760
Feb 27 15:04:06 snort[23167]:   Topmost releasable block (keepcost):
102576
Feb 27 15:04:06 snort[23167]:
===============================================================================
Feb 27 15:04:06 snort[23167]: Packet I/O Totals:
Feb 27 15:04:06 snort[23167]:    Received:      8498408
Feb 27 15:04:06 snort[23167]:    Analyzed:      8498408 (100.000%)
Feb 27 15:04:06 snort[23167]:     Dropped:            0 (  0.000%)
Feb 27 15:04:06 snort[23167]:    Filtered:            0 (  0.000%)
Feb 27 15:04:06 snort[23167]: Outstanding:            0 (  0.000%)
Feb 27 15:04:06 snort[23167]:    Injected:            0
Feb 27 15:04:06 snort[23167]:
===============================================================================
Feb 27 15:04:06 snort[23167]: Breakdown by protocol (includes rebuilt
packets):
Feb 27 15:04:06 snort[23167]:         Eth:      8537764 (100.000%)
Feb 27 15:04:06 snort[23167]:        VLAN:            0 (  0.000%)
Feb 27 15:04:06 snort[23167]:         IP4:      8510095 ( 99.676%)
Feb 27 15:04:06 snort[23167]:        Frag:            0 (  0.000%)
Feb 27 15:04:06 snort[23167]:        ICMP:        27312 (  0.320%)
Feb 27 15:04:06 snort[23167]:         UDP:       204961 (  2.401%)
Feb 27 15:04:06 snort[23167]:         TCP:      6763077 ( 79.214%)
Feb 27 15:04:06 snort[23167]:         IP6:          282 (  0.003%)
Feb 27 15:04:06 snort[23167]:     IP6 Ext:          282 (  0.003%)
Feb 27 15:04:06 snort[23167]:    IP6 Opts:            0 (  0.000%)
Feb 27 15:04:06 snort[23167]:       Frag6:            0 (  0.000%)
Feb 27 15:04:06 snort[23167]:       ICMP6:          282 (  0.003%)
Feb 27 15:04:06 snort[23167]:        UDP6:            0 (  0.000%)
Feb 27 15:04:06 snort[23167]:        TCP6:            0 (  0.000%)
Feb 27 15:04:06 snort[23167]:      Teredo:            0 (  0.000%)
Feb 27 15:04:06 snort[23167]:     ICMP-IP:            0 (  0.000%)
Feb 27 15:04:06 snort[23167]:     IP4/IP4:            0 (  0.000%)
Feb 27 15:04:06 snort[23167]:     IP4/IP6:            0 (  0.000%)
Feb 27 15:04:06 snort[23167]:     IP6/IP4:            0 (  0.000%)
Feb 27 15:04:06 snort[23167]:     IP6/IP6:            0 (  0.000%)
Feb 27 15:04:06 snort[23167]:         GRE:            0 (  0.000%)
Feb 27 15:04:06 snort[23167]:     GRE Eth:            0 (  0.000%)
Feb 27 15:04:06 snort[23167]:    GRE VLAN:            0 (  0.000%)
Feb 27 15:04:06 snort[23167]:     GRE IP4:            0 (  0.000%)
Feb 27 15:04:06 snort[23167]:     GRE IP6:            0 (  0.000%)
Feb 27 15:04:06 snort[23167]: GRE IP6 Ext:            0 (  0.000%)
Feb 27 15:04:06 snort[23167]:    GRE PPTP:            0 (  0.000%)
Feb 27 15:04:06 snort[23167]:     GRE ARP:            0 (  0.000%)
Feb 27 15:04:06 snort[23167]:     GRE IPX:            0 (  0.000%)
Feb 27 15:04:06 snort[23167]:    GRE Loop:            0 (  0.000%)
Feb 27 15:04:06 snort[23167]:        MPLS:            0 (  0.000%)
Feb 27 15:04:06 snort[23167]:         ARP:        27387 (  0.321%)
Feb 27 15:04:06 snort[23167]:         IPX:            0 (  0.000%)
Feb 27 15:04:06 snort[23167]:    Eth Loop:            0 (  0.000%)
Feb 27 15:04:06 snort[23167]:    Eth Disc:            0 (  0.000%)
Feb 27 15:04:06 snort[23167]:    IP4 Disc:      1514740 ( 17.742%)
Feb 27 15:04:06 snort[23167]:    IP6 Disc:            0 (  0.000%)
Feb 27 15:04:06 snort[23167]:    TCP Disc:            0 (  0.000%)
Feb 27 15:04:06 snort[23167]:    UDP Disc:            0 (  0.000%)
Feb 27 15:04:06 snort[23167]:   ICMP Disc:            0 (  0.000%)
Feb 27 15:04:06 snort[23167]: All Discard:      1514740 ( 17.742%)
Feb 27 15:04:06 snort[23167]:       Other:            5 (  0.000%)
Feb 27 15:04:06 snort[23167]: Bad Chk Sum:      1230372 ( 14.411%)
Feb 27 15:04:06 snort[23167]:     Bad TTL:            0 (  0.000%)
Feb 27 15:04:06 snort[23167]:      S5 G 1:        10861 (  0.127%)
Feb 27 15:04:06 snort[23167]:      S5 G 2:        28496 (  0.334%)
Feb 27 15:04:06 snort[23167]:       Total:      8537764
Feb 27 15:04:06 snort[23167]:
===============================================================================
Feb 27 15:04:06 snort[23167]: Action Stats:
Feb 27 15:04:06 snort[23167]:      Alerts:            0 (  0.000%)
Feb 27 15:04:06 snort[23167]:      Logged:            0 (  0.000%)
Feb 27 15:04:06 snort[23167]:      Passed:            0 (  0.000%)
Feb 27 15:04:06 snort[23167]: Limits:
Feb 27 15:04:06 snort[23167]:       Match:            0
Feb 27 15:04:06 snort[23167]:       Queue:            0
Feb 27 15:04:06 snort[23167]:         Log:            0
Feb 27 15:04:06 snort[23167]:       Event:            0
Feb 27 15:04:06 snort[23167]:       Alert:            0
Feb 27 15:04:06 snort[23167]: Verdicts:
Feb 27 15:04:06 snort[23167]:       Allow:      8496786 ( 99.981%)
Feb 27 15:04:06 snort[23167]:       Block:            0 (  0.000%)
Feb 27 15:04:06 snort[23167]:     Replace:            0 (  0.000%)
Feb 27 15:04:06 snort[23167]:   Whitelist:         1621 (  0.019%)
Feb 27 15:04:06 snort[23167]:   Blacklist:            0 (  0.000%)
Feb 27 15:04:06 snort[23167]:      Ignore:            0 (  0.000%)
Feb 27 15:04:06 snort[23167]:
===============================================================================
Feb 27 15:04:06 snort[23167]: Frag3 statistics:
Feb 27 15:04:06 snort[23167]:         Total Fragments: 0
Feb 27 15:04:06 snort[23167]:       Frags Reassembled: 0
Feb 27 15:04:06 snort[23167]:                Discards: 0
Feb 27 15:04:06 snort[23167]:           Memory Faults: 0
Feb 27 15:04:06 snort[23167]:                Timeouts: 0
Feb 27 15:04:06 snort[23167]:                Overlaps: 0
Feb 27 15:04:06 snort[23167]:               Anomalies: 0
Feb 27 15:04:06 snort[23167]:                  Alerts: 0
Feb 27 15:04:06 snort[23167]:                   Drops: 0
Feb 27 15:04:06 snort[23167]:      FragTrackers Added: 0
Feb 27 15:04:06 snort[23167]:     FragTrackers Dumped: 0
Feb 27 15:04:06 snort[23167]: FragTrackers Auto Freed: 0
Feb 27 15:04:06 snort[23167]:     Frag Nodes Inserted: 0
Feb 27 15:04:06 snort[23167]:      Frag Nodes Deleted: 0
Feb 27 15:04:06 snort[23167]:
===============================================================================
Feb 27 15:04:06 snort[23167]: Stream5 statistics:
Feb 27 15:04:06 snort[23167]:             Total sessions: 272938
Feb 27 15:04:06 snort[23167]:               TCP sessions: 255727
Feb 27 15:04:06 snort[23167]:               UDP sessions: 17211
Feb 27 15:04:06 snort[23167]:              ICMP sessions: 0
Feb 27 15:04:06 snort[23167]:                IP sessions: 0
Feb 27 15:04:06 snort[23167]:                 TCP Prunes: 0
Feb 27 15:04:06 snort[23167]:                 UDP Prunes: 0
Feb 27 15:04:06 snort[23167]:                ICMP Prunes: 0
Feb 27 15:04:06 snort[23167]:                  IP Prunes: 0
Feb 27 15:04:06 snort[23167]: TCP StreamTrackers Created: 255897
Feb 27 15:04:06 snort[23167]: TCP StreamTrackers Deleted: 255349
Feb 27 15:04:06 snort[23167]:               TCP Timeouts: 266
Feb 27 15:04:06 snort[23167]:               TCP Overlaps: 118
Feb 27 15:04:06 snort[23167]:        TCP Segments Queued: 737031
Feb 27 15:04:06 snort[23167]:      TCP Segments Released: 736763
Feb 27 15:04:06 snort[23167]:        TCP Rebuilt Packets: 306435
Feb 27 15:04:06 snort[23167]:          TCP Segments Used: 711696
Feb 27 15:04:06 snort[23167]:               TCP Discards: 8308
Feb 27 15:04:06 snort[23167]:                   TCP Gaps: 66562
Feb 27 15:04:06 snort[23167]:       UDP Sessions Created: 23942
Feb 27 15:04:06 snort[23167]:       UDP Sessions Deleted: 10211
Feb 27 15:04:06 snort[23167]:               UDP Timeouts: 6731
Feb 27 15:04:06 snort[23167]:               UDP Discards: 0
Feb 27 15:04:06 snort[23167]:                     Events: 33307
Feb 27 15:04:06 snort[23167]:            Internal Events: 0
Feb 27 15:04:06 snort[23167]:            TCP Port Filter
Feb 27 15:04:06 snort[23167]:                   Filtered: 0
Feb 27 15:04:06 snort[23167]:                  Inspected: 0
Feb 27 15:04:06 snort[23167]:                    Tracked: 5590053
Feb 27 15:04:06 snort[23167]:            UDP Port Filter
Feb 27 15:04:06 snort[23167]:                   Filtered: 0
Feb 27 15:04:06 snort[23167]:                  Inspected: 5225
Feb 27 15:04:06 snort[23167]:                    Tracked: 17211
Feb 27 15:04:06 snort[23167]:
===============================================================================
Feb 27 15:04:06 snort[23167]: HTTP Inspect - encodings (Note:
stream-reassembled packets included):
Feb 27 15:04:06 snort[23167]:     POST methods:                         657
Feb 27 15:04:06 snort[23167]:     GET methods:
33120
Feb 27 15:04:06 snort[23167]:     HTTP Request Headers extracted:
34016
Feb 27 15:04:06 snort[23167]:     HTTP Request Cookies extracted:
25326
Feb 27 15:04:06 snort[23167]:     Post parameters extracted:            657
Feb 27 15:04:06 snort[23167]:     HTTP response Headers extracted:      9083
Feb 27 15:04:06 snort[23167]:     HTTP Response Cookies extracted:      98
Feb 27 15:04:06 snort[23167]:     Unicode:                              0
Feb 27 15:04:06 snort[23167]:     Double unicode:                       0
Feb 27 15:04:06 snort[23167]:     Non-ASCII representable:              0
Feb 27 15:04:06 snort[23167]:     Directory traversals:                 0
Feb 27 15:04:06 snort[23167]:     Extra slashes ("//"):                 4045
Feb 27 15:04:06 snort[23167]:     Self-referencing paths ("./"):        0
Feb 27 15:04:06 snort[23167]:     HTTP Response Gzip packets extracted: 0
Feb 27 15:04:06 snort[23167]:     Gzip Compressed Data Processed:       n/a
Feb 27 15:04:06 snort[23167]:     Gzip Decompressed Data Processed:     n/a
Feb 27 15:04:06 snort[23167]:     Total packets processed:
1851525
Feb 27 15:04:06 snort[23167]:
===============================================================================
Feb 27 15:04:06 snort[23167]: SMTP Preprocessor Statistics
Feb 27 15:04:06 snort[23167]:   Total
sessions                                    : 0
Feb 27 15:04:06 snort[23167]:   Max concurrent
sessions                           : 0
Feb 27 15:04:06 snort[23167]:
===============================================================================
Feb 27 15:04:06 snort[23167]: dcerpc2 Preprocessor Statistics
Feb 27 15:04:06 snort[23167]:   Total sessions: 0
Feb 27 15:04:06 snort[23167]:
===============================================================================
Feb 27 15:04:06 snort[23167]: SSL Preprocessor:
Feb 27 15:04:06 snort[23167]:    SSL packets decoded: 892031
Feb 27 15:04:06 snort[23167]:           Client Hello: 389752
Feb 27 15:04:06 snort[23167]:           Server Hello: 793
Feb 27 15:04:06 snort[23167]:            Certificate: 908
Feb 27 15:04:06 snort[23167]:            Server Done: 382480
Feb 27 15:04:06 snort[23167]:    Client Key Exchange: 30685
Feb 27 15:04:06 snort[23167]:    Server Key Exchange: 0
Feb 27 15:04:06 snort[23167]:          Change Cipher: 384430
Feb 27 15:04:06 snort[23167]:               Finished: 0
Feb 27 15:04:06 snort[23167]:     Client Application: 440228
Feb 27 15:04:06 snort[23167]:     Server Application: 427
Feb 27 15:04:06 snort[23167]:                  Alert: 21387
Feb 27 15:04:06 snort[23167]:   Unrecognized records: 191082
Feb 27 15:04:06 snort[23167]:   Completed handshakes: 0
Feb 27 15:04:06 snort[23167]:         Bad handshakes: 121
Feb 27 15:04:06 snort[23167]:       Sessions ignored: 427
Feb 27 15:04:06 snort[23167]:     Detection disabled: 19941
Feb 27 15:04:06 snort[23167]:
===============================================================================
Feb 27 15:04:06 snort[23167]: SIP Preprocessor Statistics
Feb 27 15:04:06 snort[23167]:   Total sessions: 3
Feb 27 15:04:06 snort[23167]:   SIP anomalies : 1
Feb 27 15:04:06 snort[23167]:   Requests: 0
Feb 27 15:04:06 snort[23167]:           invite:   0
Feb 27 15:04:06 snort[23167]:           cancel:   0
Feb 27 15:04:06 snort[23167]:              ack:   0
Feb 27 15:04:06 snort[23167]:              bye:   0
Feb 27 15:04:06 snort[23167]:         register:   0
Feb 27 15:04:06 snort[23167]:          options:   0
Feb 27 15:04:06 snort[23167]:            refer:   0
Feb 27 15:04:06 snort[23167]:        subscribe:   0
Feb 27 15:04:06 snort[23167]:           update:   0
Feb 27 15:04:06 snort[23167]:             join:   0
Feb 27 15:04:06 snort[23167]:             info:   0
Feb 27 15:04:06 snort[23167]:          message:   0
Feb 27 15:04:06 snort[23167]:           notify:   0
Feb 27 15:04:06 snort[23167]:            prack:   0
Feb 27 15:04:06 snort[23167]:   Responses: 0
Feb 27 15:04:06 snort[23167]:              1xx:   0
Feb 27 15:04:06 rsyslogd-2177: imuxsock begins to drop messages from pid
23167 due to rate-limiting

Thank you,

  - Mirek



On Thu, Feb 27, 2014 at 2:50 PM, Hui Cao (huica) <huica at ...589...> wrote:

>  HI Mirek,
>
>  Snort memory usage might increase constantly when more sessions are
> tracked. After some point, it will stabilize. If you saw memory never stops
> increasing even all the sessions used up, it might indicate some memory
> issue. Based on your data, it looks like ok at this level. What's the snort
> stats and snort configuration? You can use kill -USR1 Snort_PID  to get
> snort stats if you don't want to stop snort.
>
>  Best,
> Hui.
>
>   From: Mirek Suliba <msuliba at ...11827...>
> Date: Thursday, February 27, 2014 at 3:37 PM
> To: "snort-users at lists.sourceforge.net" <snort-users at lists.sourceforge.net
> >
> Subject: [Snort-users] Fwd: Snort 2.9.6.0 memory leak?
>
>         Hello,
>
>  I have just installed my first instance of Snort and found that after
> putting traffic through it Snort memory usage is constantly growing. Below
> are checks done every hour using "top" command:
>
>  Time    VIRT    RES    %MEM
>  9:00     596m   240m   12.9
>  10:00   596m   310m    16.5
>  11:00   596m   386m    20.6
>  12:00   596m   456m    24.3
>
>  Is this normal behavior for Snort? If not what setting should I change
> to fix it?
>
>  This installation of Snort is for monitoring traffic only on local
> server (not promiscuous mode).
>
>  System is CentOS 6.4 with 2 GB of memory. Below is Snort information:
>
> # snort -V
>
>    ,,_     -*> Snort! <*-
>   o"  )~   Version 2.9.6.0 GRE (Build 47)
>    ''''    By Martin Roesch & The Snort Team:
> http://www.snort.org/snort/snort-team
>            Copyright (C) 2014 Cisco and/or its affiliates. All rights
> reserved.
>            Copyright (C) 1998-2013 Sourcefire, Inc., et al.
>            Using libpcap version 1.0.0
>            Using PCRE version: 7.8 2008-09-05
>            Using ZLIB version: 1.2.3
>
>  Snort command:
>
> /usr/sbin/snort -A fast -b -d -D -i eth0 -u snort -g snort -c
> /etc/snort/snort.conf -l /var/log/snort
>
>  Content of snort.conf file:
>
> #--------------------------------------------------
> #   VRT Rule Packages Snort.conf
> #
> #   For more information visit us at:
> #     http://www.snort.org                   Snort Website
> #     http://vrt-blog.snort.org/    Sourcefire VRT Blog
> #
> #     Mailing list Contact:      snort-sigs at lists.sourceforge.net
> #     False Positive reports:    fp at ...1935...
> #     Snort bugs:                bugs at ...950...
> #
> #     Compatible with Snort Versions:
> #     VERSIONS : 2.9.6.0
> #
> #     Snort build options:
> #     OPTIONS : --enable-gre --enable-mpls --enable-targetbased
> --enable-ppm --enable-perfprofiling --enable-zlib --enable-activ
> e-response --enable-normalizer --enable-reload --enable-react
> --enable-flexresp3
> #
> #     Additional information:
> #     This configuration file enables active response, to run snort in
> #     test mode -T you are required to supply an interface -i <interface>
> #     or test mode will fail to fully validate the configuration and
> #     exit with a FATAL error
> #--------------------------------------------------
>
> ###################################################
> # This file contains a sample snort configuration.
> # You should take the following steps to create your own custom
> configuration:
> #
> #  1) Set the network variables.
> #  2) Configure the decoder
> #  3) Configure the base detection engine
> #  4) Configure dynamic loaded libraries
> #  5) Configure preprocessors
> #  6) Configure output plugins
> #  7) Customize your rule set
> #  8) Customize preprocessor and decoder rule set
> #  9) Customize shared object rule set
> ###################################################
>
> ###################################################
> # Step #1: Set the network variables.  For more information, see
> README.variables
> ###################################################
>
> # Setup the network addresses you are protecting
> ipvar HOME_NET any
>
> # Set up the external network addresses. Leave as "any" in most situations
> ipvar EXTERNAL_NET any
>
> # List of DNS servers on your network
> ipvar DNS_SERVERS $HOME_NET
>
> # List of SMTP servers on your network
> ipvar SMTP_SERVERS $HOME_NET
>
> # List of web servers on your network
> ipvar HTTP_SERVERS $HOME_NET
>
> # List of sql servers on your network
> ipvar SQL_SERVERS $HOME_NET
>
> # List of telnet servers on your network
> ipvar TELNET_SERVERS $HOME_NET
>
> # List of ssh servers on your network
> ipvar SSH_SERVERS $HOME_NET
>
> # List of ftp servers on your network
> ipvar FTP_SERVERS $HOME_NET
>
> # List of sip servers on your network
> ipvar SIP_SERVERS $HOME_NET
>
> # List of ports you run web servers on
> portvar HTTP_PORTS
> [36,80,81,82,83,84,85,86,87,88,89,90,311,383,555,591,593,631,801,808,818,901,972,1158,1220,1414,1533,1741,183
>
> 0,2231,2301,2381,2809,3029,3037,3057,3128,3443,3702,4000,4343,4848,5117,5250,6080,6173,6988,7000,7001,7071,7144,7145,7510,7770,7
>
> 777,7779,8000,8008,8014,8028,8080,8081,8082,8085,8088,8090,8118,8123,8180,8181,8222,8243,8280,8300,8500,8509,8800,8888,8899,9000
>
> ,9060,9080,9090,9091,9111,9443,9999,10000,11371,12601,15489,29991,33300,34412,34443,34444,41080,44449,50000,50002,51423,53331,55
> 252,55555,56712]
>
> # List of ports you want to look for SHELLCODE on.
> portvar SHELLCODE_PORTS !80
>
> # List of ports you might see oracle attacks on
> portvar ORACLE_PORTS 1024:
>
> # List of ports you want to look for SSH connections on:
> portvar SSH_PORTS 22
>
> # List of ports you run ftp servers on
> portvar FTP_PORTS [21,2100,3535]
>
> # List of ports you run SIP servers on
> portvar SIP_PORTS [5060,5061,5600]
>
> # List of file data ports for file inspection
> portvar FILE_DATA_PORTS [$HTTP_PORTS,110,143]
>
> # List of GTP ports for GTP preprocessor
> portvar GTP_PORTS [2123,2152,3386]
>
> # other variables, these should not be modified
> ipvar AIM_SERVERS [
> 64.12.24.0/23,64.12.28.0/23,64.12.161.0/24,64.12.163.0/24,64.12.200.0/24,205.188.3.0/24,205.188.5.0/24,205.18
> 8.7.0/24,205.188.9.0/24,205.188.153.0/24,205.188.179.0/24,205.188.248.0/24
> ]
>
> # Path to your rules files (this can be a relative path)
> # Note for Windows users:  You are advised to make this an absolute path,
> # such as:  c:\snort\rules
> var RULE_PATH /etc/snort/rules
> var SO_RULE_PATH /etc/snort/so_rules
> var PREPROC_RULE_PATH /etc/snort/preproc_rules
>
> # If you are using reputation preprocessor set these
> var WHITE_LIST_PATH /etc/snort/rules
> var BLACK_LIST_PATH /etc/snort/rules
>
> ###################################################
> # Step #2: Configure the decoder.  For more information, see README.decode
> ###################################################
>
> # Disable promiscuous mode
> config no_promisc
>
> # Stop generic decode events:
> config disable_decode_alerts
>
> # Stop Alerts on experimental TCP options
> config disable_tcpopt_experimental_alerts
>
> # Stop Alerts on obsolete TCP options
> config disable_tcpopt_obsolete_alerts
>
> # Stop Alerts on T/TCP alerts
> config disable_tcpopt_ttcp_alerts
>
> # Stop Alerts on all other TCPOption type events:
> config disable_tcpopt_alerts
>
> # Stop Alerts on invalid ip options
> config disable_ipopt_alerts
>
> # Alert if value in length field (IP, TCP, UDP) is greater th elength of
> the packet
> # config enable_decode_oversized_alerts
>
> # Same as above, but drop packet if in Inline mode (requires
> enable_decode_oversized_alerts)
> # config enable_decode_oversized_drops
>
> # Configure IP / TCP checksum mode
> config checksum_mode: all
>
> # Configure maximum number of flowbit references.  For more information,
> see README.flowbits
> # config flowbits_size: 64
>
> # Configure ports to ignore
> # config ignore_ports: tcp 21 6667:6671 1356
> # config ignore_ports: udp 1:17 53
>
> # Configure active response for non inline operation. For more
> information, see REAMDE.active
> # config response: eth0 attempts 2
>
> # Configure DAQ related options for inline operation. For more
> information, see README.daq
> #
> # config daq: <type>
> # config daq_dir: <dir>
> # config daq_mode: <mode>
> # config daq_var: <var>
> #
> # <type> ::= pcap | afpacket | dump | nfq | ipq | ipfw
> # <mode> ::= read-file | passive | inline
> # <var> ::= arbitrary <name>=<value passed to DAQ
> # <dir> ::= path as to where to look for DAQ module so's
>
> # Configure specific UID and GID to run snort as after dropping privs. For
> more information see snort -h command line options
> #
> # config set_gid:
> # config set_uid:
>
> # Configure default snaplen. Snort defaults to MTU of in use interface.
> For more information see README
> #
> # config snaplen:
> #
>
> # Configure default bpf_file to use for filtering what traffic reaches
> snort. For more information see snort -h command line opt
> ions (-F)
> #
> # config bpf_file:
> #
>
> # Configure default log directory for snort to log to.  For more
> information see snort -h command line options (-l)
> #
> # config logdir:
>
>
> ###################################################
> # Step #3: Configure the base detection engine.  For more information,
> see  README.decode
> ###################################################
>
> # Configure PCRE match limitations
> config pcre_match_limit: 3500
> config pcre_match_limit_recursion: 1500
>
> # Configure the detection engine  See the Snort Manual, Configuring Snort
> - Includes - Config
> config detection: search-method ac-split search-optimize max-pattern-len 20
>
> # Configure the event queue.  For more information, see README.event_queue
> config event_queue: max_queue 8 log 5 order_events content_length
>
> ###################################################
> ## Configure GTP if it is to be used.
> ## For more information, see README.GTP
> ####################################################
>
> # config enable_gtp
>
> ###################################################
> # Per packet and rule latency enforcement
> # For more information see README.ppm
> ###################################################
>
> # Per Packet latency configuration
> #config ppm: max-pkt-time 250, \
> #   fastpath-expensive-packets, \
> #   pkt-log
>
> # Per Rule latency configuration
> #config ppm: max-rule-time 200, \
> #   threshold 3, \
> #   suspend-expensive-rules, \
> #   suspend-timeout 20, \
> #   rule-log alert
>
> ###################################################
> # Configure Perf Profiling for debugging
> # For more information see README.PerfProfiling
> ###################################################
>
> #config profile_rules: print all, sort avg_ticks
> #config profile_preprocs: print all, sort avg_ticks
>
> ###################################################
> # Configure protocol aware flushing
> # For more information see README.stream5
> ###################################################
> config paf_max: 16000
>
> ###################################################
> # Step #4: Configure dynamic loaded libraries.
> # For more information, see Snort Manual, Configuring Snort - Dynamic
> Modules
> ###################################################
>
> # path to dynamic preprocessor libraries
> # dynamicpreprocessor directory /usr/local/lib/snort_dynamicpreprocessor/
> dynamicpreprocessor directory /usr/lib64/snort-2.9.6.0_dynamicpreprocessor
>
> # path to base preprocessor engine
> # dynamicengine /usr/local/lib/snort_dynamicengine/libsf_engine.so
> dynamicengine /usr/lib64/snort-2.9.6.0_dynamicengine/libsf_engine.so
>
> # path to dynamic rules libraries
> # dynamicdetection directory /usr/local/lib/snort_dynamicrules
> dynamicdetection directory /etc/snort/so_rules/precompiled/RHEL-6-0/x86-64/
> 2.9.6.0
>
> ###################################################
> # Step #5: Configure preprocessors
> # For more information, see the Snort Manual, Configuring Snort -
> Preprocessors
> ###################################################
>
> # GTP Control Channle Preprocessor. For more information, see README.GTP
> # preprocessor gtp: ports { 2123 3386 2152 }
>
> # Inline packet normalization. For more information, see README.normalize
> # Does nothing in IDS mode
> preprocessor normalize_ip4
> preprocessor normalize_tcp: ips ecn stream
> preprocessor normalize_icmp4
> preprocessor normalize_ip6
> preprocessor normalize_icmp6
>
> # Target-based IP defragmentation.  For more inforation, see README.frag3
> preprocessor frag3_global: max_frags 65536
> preprocessor frag3_engine: policy windows detect_anomalies overlap_limit
> 10 min_fragment_length 100 timeout 180
>
> # Target-Based stateful inspection/stream reassembly.  For more
> inforation, see README.stream5
> preprocessor stream5_global: track_tcp yes, \
>    track_udp yes, \
>    track_icmp no, \
>    max_tcp 262144, \
>    max_udp 131072, \
>    max_active_responses 2, \
>    min_response_seconds 5
> preprocessor stream5_tcp: policy windows, detect_anomalies, require_3whs
> 180, \
>    overlap_limit 10, small_segments 3 bytes 150, timeout 180, \
>     ports client 21 22 23 25 42 53 70 79 109 110 111 113 119 135 136 137
> 139 143 \
>         161 445 513 514 587 593 691 1433 1521 1741 2100 3306 6070 6665
> 6666 6667 6668 6669 \
>         7000 8181 32770 32771 32772 32773 32774 32775 32776 32777 32778
> 32779, \
>     ports both 36 80 81 82 83 84 85 86 87 88 89 90 110 311 383 443 465 563
> 555 591 593 631 636 801 808 818 901 972 989 992 993 9
> 94 995 1158 1220 1414 1533 1741 1830 2231 2301 2381 2809 3029 3037 3057
> 3128 3443 3702 4000 4343 4848 5117 5250 6080 6173 6988 7
> 907 7000 7001 7071 7144 7145 7510 7802 7770 7777 7779 \
>         7801 7900 7901 7902 7903 7904 7905 7906 7908 7909 7910 7911 7912
> 7913 7914 7915 7916 \
>         7917 7918 7919 7920 8000 8008 8014 8028 8080 8081 8082 8085 8088
> 8090 8118 8123 8180 8181 8222 8243 8280 8300 8500 8509
> 8800 8888 8899 9000 9060 9080 9090 9091 9111 9443 9999 10000 11371 12601
> 15489 29991 33300 34412 34443 34444 41080 44449 50000 5
> 0002 51423 53331 55252 55555 56712
> preprocessor stream5_udp: timeout 180
>
> # performance statistics.  For more information, see the Snort Manual,
> Configuring Snort - Preprocessors - Performance Monitor
> # preprocessor perfmonitor: time 300 file /var/snort/snort.stats pktcnt
> 10000
>
> # HTTP normalization and anomaly detection.  For more information, see
> README.http_inspect
> preprocessor http_inspect: global iis_unicode_map unicode.map 1252
> compress_depth 65535 decompress_depth 65535
> preprocessor http_inspect_server: server default \
>     http_methods { GET POST PUT SEARCH MKCOL COPY MOVE LOCK UNLOCK NOTIFY
> POLL BCOPY BDELETE BMOVE LINK UNLINK OPTIONS HEAD DELE
> TE TRACE TRACK CONNECT SOURCE SUBSCRIBE UNSUBSCRIBE PROPFIND PROPPATCH
> BPROPFIND BPROPPATCH RPC_CONNECT PROXY_SUCCESS BITS_POST
> CCM_POST SMS_POST RPC_IN_DATA RPC_OUT_DATA RPC_ECHO_DATA } \
>     chunk_length 500000 \
>     server_flow_depth 0 \
>     client_flow_depth 0 \
>     post_depth 65495 \
>     oversize_dir_length 500 \
>     max_header_length 750 \
>     max_headers 100 \
>     max_spaces 200 \
>     small_chunk_length { 10 5 } \
>     ports { 36 80 81 82 83 84 85 86 87 88 89 90 311 383 555 591 593 631
> 801 808 818 901 972 1158 1220 1414 1741 1830 2231 2301 2
> 381 2809 3029 3037 3057 3128 3443 3702 4000 4343 4848 5117 5250 6080 6173
> 6988 7000 7001 7071 7144 7145 7510 7770 7777 7779 8000
>  8008 8014 8028 8080 8081 8082 8085 8088 8090 8118 8123 8180 8181 8222
> 8243 8280 8300 8500 8509 8800 8888 8899 9000 9060 9080 90
> 90 9091 9111 9443 9999 10000 11371 12601 15489 29991 33300 34412 34443
> 34444 41080 44449 50000 50002 51423 53331 55252 55555 567
> 12 } \
>     non_rfc_char { 0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07 } \
>     enable_cookie \
>     extended_response_inspection \
>     inspect_gzip \
>     normalize_utf \
>     unlimited_decompress \
>     normalize_javascript \
>     apache_whitespace no \
>     ascii no \
>     bare_byte no \
>     directory no \
>     double_decode no \
>     iis_backslash no \
>     iis_delimiter no \
>     iis_unicode no \
>     multi_slash no \
>     utf_8 no \
>     u_encode yes \
>     webroot no
>
> # ONC-RPC normalization and anomaly detection.  For more information, see
> the Snort Manual, Configuring Snort - Preprocessors -
> RPC Decode
> preprocessor rpc_decode: 111 32770 32771 32772 32773 32774 32775 32776
> 32777 32778 32779 no_alert_multiple_requests no_alert_lar
> ge_fragments no_alert_incomplete
>
> # Back Orifice detection.
> preprocessor bo
>
> # FTP / Telnet normalization and anomaly detection.  For more information,
> see README.ftptelnet
> preprocessor ftp_telnet: global inspection_type stateful encrypted_traffic
> no check_encrypted
> preprocessor ftp_telnet_protocol: telnet \
>     ayt_attack_thresh 20 \
>     normalize ports { 23 } \
>     detect_anomalies
> preprocessor ftp_telnet_protocol: ftp server default \
>     def_max_param_len 100 \
>     ports { 21 2100 3535 } \
>     telnet_cmds yes \
>     ignore_telnet_erase_cmds yes \
>     ftp_cmds { ABOR ACCT ADAT ALLO APPE AUTH CCC CDUP } \
>     ftp_cmds { CEL CLNT CMD CONF CWD DELE ENC EPRT } \
>     ftp_cmds { EPSV ESTA ESTP FEAT HELP LANG LIST LPRT } \
>     ftp_cmds { LPSV MACB MAIL MDTM MIC MKD MLSD MLST } \
>     ftp_cmds { MODE NLST NOOP OPTS PASS PASV PBSZ PORT } \
>     ftp_cmds { PROT PWD QUIT REIN REST RETR RMD RNFR } \
>     ftp_cmds { RNTO SDUP SITE SIZE SMNT STAT STOR STOU } \
>     ftp_cmds { STRU SYST TEST TYPE USER XCUP XCRC XCWD } \
>     ftp_cmds { XMAS XMD5 XMKD XPWD XRCP XRMD XRSQ XSEM } \
>     ftp_cmds { XSEN XSHA1 XSHA256 } \
>     alt_max_param_len 0 { ABOR CCC CDUP ESTA FEAT LPSV NOOP PASV PWD QUIT
> REIN STOU SYST XCUP XPWD } \
>     alt_max_param_len 200 { ALLO APPE CMD HELP NLST RETR RNFR STOR STOU
> XMKD } \
>     alt_max_param_len 256 { CWD RNTO } \
>     alt_max_param_len 400 { PORT } \
>     alt_max_param_len 512 { SIZE } \
>     chk_str_fmt { ACCT ADAT ALLO APPE AUTH CEL CLNT CMD } \
>     chk_str_fmt { CONF CWD DELE ENC EPRT EPSV ESTP HELP } \
>     chk_str_fmt { LANG LIST LPRT MACB MAIL MDTM MIC MKD } \
>     chk_str_fmt { MLSD MLST MODE NLST OPTS PASS PBSZ PORT } \
>     chk_str_fmt { PROT REST RETR RMD RNFR RNTO SDUP SITE } \
>     chk_str_fmt { SIZE SMNT STAT STOR STRU TEST TYPE USER } \
>     chk_str_fmt { XCRC XCWD XMAS XMD5 XMKD XRCP XRMD XRSQ } \
>     chk_str_fmt { XSEM XSEN XSHA1 XSHA256 } \
>     cmd_validity ALLO < int [ char R int ] > \
>     cmd_validity EPSV < [ { char 12 | char A char L char L } ] > \
>     cmd_validity MACB < string > \
>     cmd_validity MDTM < [ date nnnnnnnnnnnnnn[.n[n[n]]] ] string > \
>     cmd_validity MODE < char ASBCZ > \
>     cmd_validity PORT < host_port > \
>     cmd_validity PROT < char CSEP > \
>     cmd_validity STRU < char FRPO [ string ] > \
>     cmd_validity TYPE < { char AE [ char NTC ] | char I | char L [ number
> ] } >
> preprocessor ftp_telnet_protocol: ftp client default \
>     max_resp_len 256 \
>     bounce yes \
>     ignore_telnet_erase_cmds yes \
>     telnet_cmds yes
>
>
> # SMTP normalization and anomaly detection.  For more information, see
> README.SMTP
> preprocessor smtp: ports { 25 465 587 691 } \
>     inspection_type stateful \
>     b64_decode_depth 0 \
>     qp_decode_depth 0 \
>     bitenc_decode_depth 0 \
>     uu_decode_depth 0 \
>     log_mailfrom \
>     log_rcptto \
>     log_filename \
>     log_email_hdrs \
>     normalize cmds \
>     normalize_cmds { ATRN AUTH BDAT CHUNKING DATA DEBUG EHLO EMAL ESAM
> ESND ESOM ETRN EVFY } \
>     normalize_cmds { EXPN HELO HELP IDENT MAIL NOOP ONEX QUEU QUIT RCPT
> RSET SAML SEND SOML } \
>     normalize_cmds { STARTTLS TICK TIME TURN TURNME VERB VRFY X-ADAT
> X-DRCP X-ERCP X-EXCH50 } \
>     normalize_cmds { X-EXPS X-LINK2STATE XADR XAUTH XCIR XEXCH50 XGEN
> XLICENSE XQUE XSTA XTRN XUSR } \
>     max_command_line_len 512 \
>     max_header_line_len 1000 \
>     max_response_line_len 512 \
>     alt_max_command_line_len 260 { MAIL } \
>     alt_max_command_line_len 300 { RCPT } \
>     alt_max_command_line_len 500 { HELP HELO ETRN EHLO } \
>     alt_max_command_line_len 255 { EXPN VRFY ATRN SIZE BDAT DEBUG EMAL
> ESAM ESND ESOM EVFY IDENT NOOP RSET } \
>     alt_max_command_line_len 246 { SEND SAML SOML AUTH TURN ETRN DATA RSET
> QUIT ONEX QUEU STARTTLS TICK TIME TURNME VERB X-EXPS
> X-LINK2STATE XADR XAUTH XCIR XEXCH50 XGEN XLICENSE XQUE XSTA XTRN XUSR } \
>     valid_cmds { ATRN AUTH BDAT CHUNKING DATA DEBUG EHLO EMAL ESAM ESND
> ESOM ETRN EVFY } \
>     valid_cmds { EXPN HELO HELP IDENT MAIL NOOP ONEX QUEU QUIT RCPT RSET
> SAML SEND SOML } \
>     valid_cmds { STARTTLS TICK TIME TURN TURNME VERB VRFY X-ADAT X-DRCP
> X-ERCP X-EXCH50 } \
>     valid_cmds { X-EXPS X-LINK2STATE XADR XAUTH XCIR XEXCH50 XGEN XLICENSE
> XQUE XSTA XTRN XUSR } \
>     xlink2state { enabled }
>
> # Portscan detection.  For more information, see README.sfportscan
> # preprocessor sfportscan: proto  { all } memcap { 10000000 } sense_level
> { low }
>
> # ARP spoof detection.  For more information, see the Snort Manual -
> Configuring Snort - Preprocessors - ARP Spoof Preprocessor
> # preprocessor arpspoof
> # preprocessor arpspoof_detect_host: 192.168.40.1 f0:0f:00:f0:0f:00
>
> # SSH anomaly detection.  For more information, see README.ssh
> preprocessor ssh: server_ports { 22 } \
>                   autodetect \
>                   max_client_bytes 19600 \
>                   max_encrypted_packets 20 \
>                   max_server_version_len 100 \
>                   enable_respoverflow enable_ssh1crc32 \
>                   enable_srvoverflow enable_protomismatch
>
> # SMB / DCE-RPC normalization and anomaly detection.  For more
> information, see README.dcerpc2
> preprocessor dcerpc2: memcap 102400, events [co ]
> preprocessor dcerpc2_server: default, policy WinXP, \
>     detect [smb [139,445], tcp 135, udp 135, rpc-over-http-server 593], \
>     autodetect [tcp 1025:, udp 1025:, rpc-over-http-server 1025:], \
>     smb_max_chain 3, smb_invalid_shares ["C$", "D$", "ADMIN$"]
>
> # DNS anomaly detection.  For more information, see README.dns
> preprocessor dns: ports { 53 } enable_rdata_overflow
>
> # SSL anomaly detection and traffic bypass.  For more information, see
> README.ssl
> preprocessor ssl: ports { 443 465 563 636 989 992 993 994 995 7801 7802
> 7900 7901 7902 7903 7904 7905 7906 7907 7908 7909 7910 7
> 911 7912 7913 7914 7915 7916 7917 7918 7919 7920 }, trustservers,
> noinspect_encrypted
>
> # SDF sensitive data preprocessor.  For more information see
> README.sensitive_data
> preprocessor sensitive_data: alert_threshold 25
>
> # SIP Session Initiation Protocol preprocessor.  For more information see
> README.sip
> preprocessor sip: max_sessions 40000, \
>    ports { 5060 5061 5600 }, \
>    methods { invite \
>              cancel \
>              ack \
>              bye \
>              register \
>              options \
>              refer \
>              subscribe \
>              update \
>              join \
>              info \
>              message \
>              notify \
>              benotify \
>              do \
>              qauth \
>              sprack \
>              publish \
>              service \
>              unsubscribe \
>              prack }, \
>    max_uri_len 512, \
>    max_call_id_len 80, \
>    max_requestName_len 20, \
>    max_from_len 256, \
>    max_to_len 256, \
>    max_via_len 1024, \
>    max_contact_len 512, \
>    max_content_len 2048
>
> # IMAP preprocessor.  For more information see README.imap
> preprocessor imap: \
>    ports { 143 } \
>    b64_decode_depth 0 \
>    qp_decode_depth 0 \
>    bitenc_decode_depth 0 \
>    uu_decode_depth 0
>
> # POP preprocessor. For more information see README.pop
> preprocessor pop: \
>    ports { 110 } \
>    b64_decode_depth 0 \
>    qp_decode_depth 0 \
>    bitenc_decode_depth 0 \
>    uu_decode_depth 0
>
> # Modbus preprocessor. For more information see README.modbus
> preprocessor modbus: ports { 502 }
>
> # DNP3 preprocessor. For more information see README.dnp3
> preprocessor dnp3: ports { 20000 } \
>    memcap 262144 \
>    check_crc
>
> # Reputation preprocessor. For more information see README.reputation
> preprocessor reputation: \
>    memcap 500, \
>    priority whitelist, \
>    nested_ip inner, \
>    whitelist $WHITE_LIST_PATH/white_list.rules, \
>    blacklist $BLACK_LIST_PATH/black_list.rules
>
> ###################################################
> # Step #6: Configure output plugins
> # For more information, see Snort Manual, Configuring Snort - Output
> Modules
> ###################################################
>
> # unified2
> # Recommended for most installs
> # output unified2: filename merged.log, limit 128, nostamp,
> mpls_event_types, vlan_event_types
>
> # Additional configuration for specific types of installs
> # output alert_unified2: filename snort.alert, limit 128, nostamp
> # output log_unified2: filename snort.log, limit 128, nostamp
>
> # syslog
> # output alert_syslog: LOG_AUTH LOG_ALERT
>
> # pcap
> # output log_tcpdump: tcpdump.log
>
> # metadata reference data.  do not modify these lines
> include classification.config
> include reference.config
>
>
> ###################################################
> # Step #7: Customize your rule set
> # For more information, see Snort Manual, Writing Snort Rules
> #
> # NOTE: All categories are enabled in this conf file
> ###################################################
>
> # site specific rules
> include $RULE_PATH/local.rules
>
> include $RULE_PATH/app-detect.rules
> include $RULE_PATH/attack-responses.rules
> include $RULE_PATH/backdoor.rules
> include $RULE_PATH/bad-traffic.rules
> include $RULE_PATH/blacklist.rules
> include $RULE_PATH/botnet-cnc.rules
> include $RULE_PATH/browser-chrome.rules
> include $RULE_PATH/browser-firefox.rules
> include $RULE_PATH/browser-ie.rules
> include $RULE_PATH/browser-other.rules
> include $RULE_PATH/browser-plugins.rules
> include $RULE_PATH/browser-webkit.rules
> include $RULE_PATH/chat.rules
> include $RULE_PATH/content-replace.rules
> include $RULE_PATH/ddos.rules
> include $RULE_PATH/dns.rules
> include $RULE_PATH/dos.rules
> include $RULE_PATH/experimental.rules
> include $RULE_PATH/exploit-kit.rules
> include $RULE_PATH/exploit.rules
> include $RULE_PATH/file-executable.rules
> include $RULE_PATH/file-flash.rules
> include $RULE_PATH/file-identify.rules
> include $RULE_PATH/file-image.rules
> include $RULE_PATH/file-java.rules
> include $RULE_PATH/file-multimedia.rules
> include $RULE_PATH/file-office.rules
> include $RULE_PATH/file-other.rules
> include $RULE_PATH/file-pdf.rules
> include $RULE_PATH/finger.rules
> include $RULE_PATH/ftp.rules
> include $RULE_PATH/icmp-info.rules
> include $RULE_PATH/icmp.rules
> include $RULE_PATH/imap.rules
> include $RULE_PATH/indicator-compromise.rules
> include $RULE_PATH/indicator-obfuscation.rules
> include $RULE_PATH/indicator-scan.rules
> include $RULE_PATH/indicator-shellcode.rules
> include $RULE_PATH/info.rules
> include $RULE_PATH/malware-backdoor.rules
> include $RULE_PATH/malware-cnc.rules
> include $RULE_PATH/malware-other.rules
> include $RULE_PATH/malware-tools.rules
> include $RULE_PATH/misc.rules
> include $RULE_PATH/multimedia.rules
> include $RULE_PATH/mysql.rules
> include $RULE_PATH/netbios.rules
> include $RULE_PATH/nntp.rules
> include $RULE_PATH/oracle.rules
> include $RULE_PATH/os-linux.rules
> include $RULE_PATH/os-mobile.rules
> include $RULE_PATH/os-other.rules
> include $RULE_PATH/os-solaris.rules
> include $RULE_PATH/os-windows.rules
> include $RULE_PATH/other-ids.rules
> include $RULE_PATH/p2p.rules
> include $RULE_PATH/phishing-spam.rules
> include $RULE_PATH/policy-multimedia.rules
> include $RULE_PATH/policy-other.rules
> include $RULE_PATH/policy.rules
> include $RULE_PATH/policy-social.rules
> include $RULE_PATH/policy-spam.rules
> include $RULE_PATH/pop2.rules
> include $RULE_PATH/pop3.rules
> include $RULE_PATH/protocol-dns.rules
> include $RULE_PATH/protocol-finger.rules
> include $RULE_PATH/protocol-ftp.rules
> include $RULE_PATH/protocol-icmp.rules
> include $RULE_PATH/protocol-imap.rules
> include $RULE_PATH/protocol-nntp.rules
> include $RULE_PATH/protocol-pop.rules
> include $RULE_PATH/protocol-rpc.rules
> include $RULE_PATH/protocol-scada.rules
> include $RULE_PATH/protocol-services.rules
> include $RULE_PATH/protocol-snmp.rules
> include $RULE_PATH/protocol-telnet.rules
> include $RULE_PATH/protocol-tftp.rules
> include $RULE_PATH/protocol-voip.rules
> include $RULE_PATH/pua-adware.rules
> include $RULE_PATH/pua-other.rules
> include $RULE_PATH/pua-p2p.rules
> include $RULE_PATH/pua-toolbars.rules
> include $RULE_PATH/rpc.rules
> include $RULE_PATH/rservices.rules
> include $RULE_PATH/scada.rules
> include $RULE_PATH/scan.rules
> include $RULE_PATH/server-apache.rules
> include $RULE_PATH/server-iis.rules
> include $RULE_PATH/server-mail.rules
> include $RULE_PATH/server-mssql.rules
> include $RULE_PATH/server-mysql.rules
> include $RULE_PATH/server-oracle.rules
> include $RULE_PATH/server-other.rules
> include $RULE_PATH/server-samba.rules
> include $RULE_PATH/server-webapp.rules
> include $RULE_PATH/shellcode.rules
> include $RULE_PATH/smtp.rules
> include $RULE_PATH/snmp.rules
> include $RULE_PATH/specific-threats.rules
> include $RULE_PATH/spyware-put.rules
> include $RULE_PATH/sql.rules
> include $RULE_PATH/telnet.rules
> include $RULE_PATH/tftp.rules
> include $RULE_PATH/virus.rules
> include $RULE_PATH/voip.rules
> include $RULE_PATH/web-activex.rules
> include $RULE_PATH/web-attacks.rules
> include $RULE_PATH/web-cgi.rules
> include $RULE_PATH/web-client.rules
> include $RULE_PATH/web-coldfusion.rules
> include $RULE_PATH/web-frontpage.rules
> include $RULE_PATH/web-iis.rules
> include $RULE_PATH/web-misc.rules
> include $RULE_PATH/web-php.rules
> include $RULE_PATH/x11.rules
>
> ###################################################
> # Step #8: Customize your preprocessor and decoder alerts
> # For more information, see README.decoder_preproc_rules
> ###################################################
>
> # decoder and preprocessor event rules
> # include $PREPROC_RULE_PATH/preprocessor.rules
> # include $PREPROC_RULE_PATH/decoder.rules
> # include $PREPROC_RULE_PATH/sensitive-data.rules
>
> ###################################################
> # Step #9: Customize your Shared Object Snort Rules
> # For more information, see
> http://vrt-blog.snort.org/2009/01/using-vrt-certified-shared-object-rules.html
> ###################################################
>
> # dynamic library rules
> # include $SO_RULE_PATH/bad-traffic.rules
> # include $SO_RULE_PATH/chat.rules
> # include $SO_RULE_PATH/dos.rules
> # include $SO_RULE_PATH/exploit.rules
> # include $SO_RULE_PATH/icmp.rules
> # include $SO_RULE_PATH/imap.rules
> # include $SO_RULE_PATH/misc.rules
> # include $SO_RULE_PATH/multimedia.rules
> # include $SO_RULE_PATH/netbios.rules
> # include $SO_RULE_PATH/nntp.rules
> # include $SO_RULE_PATH/p2p.rules
> # include $SO_RULE_PATH/smtp.rules
> # include $SO_RULE_PATH/snmp.rules
> # include $SO_RULE_PATH/specific-threats.rules
> # include $SO_RULE_PATH/web-activex.rules
> # include $SO_RULE_PATH/web-client.rules
> # include $SO_RULE_PATH/web-iis.rules
> # include $SO_RULE_PATH/web-misc.rules
>
> # Event thresholding or suppression commands. See threshold.conf
> include threshold.conf
>
>
>  Thank you,
>
>    - Mirek
>
>
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://lists.snort.org/pipermail/snort-users/attachments/20140227/2638a502/attachment.html>


More information about the Snort-users mailing list